8SINN 15MM BASEPLATE + RISER PLATE I + 10" ARRI DOVETAIL PLATE

8Sinn 15mm Baseplate + Riser Plate I + 5" Arri Dovetail Plate 8Sinn accessories - Base Plate, Riser Plate used together with one of the cages listed below will help you to obtain the standard, 85mm optical center for those cameras. The whole configuration is put on the Arri Dovetail Plate for maximizing the balance if required. In the end, this three-piece system provides you with many features and the opportunity for further development. Compatibility The presented setup allows to obtain the optical center when used with the following cages: 8Sinn Z CAM E2-S6/F6/F8 Cage 8Sinn Z CAM E2 Cage 8Sinn Sony a7III / a7RIII Cage 8Sinn Sony A7RIV Cage 8Sinn Cage for Sony a7SIII 8Sinn BM Pocket Cinema Camera 4K / 6K Cage 8Sinn BM Pocket Cinema Camera 4K / 6K Half Cage 8Sinn Cage for Red Komodo Set includes 1 x 8Sinn 15mm Baseplate 1 x 8Sinn Riser Plate I 1 x 8Sinn 5" Arri Dovetail Plate Set's weight:  436g

8Sinn Arca Swiss Baseplate Kit + Arri Dovetail Plate 10” SKU: 8-15BP+8-RPII+8-ASP-RII+8-10ADP The 8Sinn Riser Plate II is designed to be combined with the included 8Sinn 15mm Baseplate and the 8Sinn Arca Swiss Plate, which is created specifically for it. All these products combined together form a set that is the base for the camera and allows quickly releasing and switching to handheld shooting. The Arca Swiss Plate is precisely shaped on the inside to be aligned with the safety locks on the Riser Plate II - there is a release pin on one side and a lever on the other. Thanks to this, when these items are connected, they’re secured from both sides. The long slot in the middle of the Arca Swiss Plate gives the ability of connecting it to a camera cage in ways adjusted to the threaded openings on the cage with the help of 1/4“ or 3/8“ mounting screws which are supplied. The 8Sinn 15mm Baseplate has two 32mm Arri Rosettes and 15mm rod openings. On the bottom, there are dovetail guide rails. Thus, the set can be connected with the 8Sinn 10" Arri Dovetail Plate and mounted on a tripod head. This makes a great solution for more complex camera rigs. Key features Safety locks on both sides Quick release system Compatible with DJI R Quick-Release Plate (Upper) 2 x 32mm Arri Rosettes 15mm rod openings Aluminum made Compatibility The presented Riser Plate allows obtaining the optical center when used with the following cages 8Sinn Z CAM E2-S6/F6/F8 Cage8Sinn Z CAM E2 Cage8Sinn Sony a7III / a7RIII Cage8Sinn Sony A7RIV Cage 8Sinn Cage for Sony a7SIII8Sinn BM Pocket Cinema Camera 4K / 6K Cage8Sinn BM Pocket Cinema Camera 4K / 6K Half Cage8Sinn Cage for Red® Komodo RED® Raptor8Sinn Cage for Panasonic GH68Sinn Panasonic S1H Cage8Sinn Cage for Canon EOS R5C8Sinn Cage for Leica SL2 / SL2-S Set includes 1 x 8Sinn 15mm Baseplate1 x 8Sinn Riser Plate II1 x 8Sinn Arca Swiss Plate1 x 8Sinn 10" Arri Dovetail Plate

8Sinn VCT Universal Shoulder Base Plate SKU: 8-VCT14SS The VCT Universal Shoulder Base Plate has been created to fulfill even the most specific demands. Standardised construction makes 8Sinn`s base plate universal, so it can be used with following camera models: Sony PXW-FS7 / PXW-FS7II / PXW-FS5 / PXW-FS5M2, Blackmagic Ursa Mini, Canon C100, Canon C200, Panasonic EVA-1 and many others. 8Sinn Shoulder Base Plate serves as integrated system and sturdy base for your camera rig. Set includes 1 x 8Sinn VCT Universal Shoulder Base PlateOptionally: 15mm rods SECURITY SYSTEMS Blocking points located at the main body are built-in in such a way as to prevent the Manfrotto 501PLONG plate from being lifted off from the VCT Universal Shoulder Base Plate. Blocking button lock and unlock the plate from the VCT Shoulder Plate. The knob function is to keep the plate in fixed position. ROD SECTION 8Sinn's product has the 15mm rods oppenings located at the front as well as at the back of its structure. Rods from the back part have their own knob for separate regulation. Frontal rods section, on the other hand, have their own adjustment system VCT - 14 MOUNT Another standard solution applied on 8Sinn Shoulder Plate is the VCT-14 Mount, compatible with Sony VCT-14 tripod adapter plates. This solution enables the possibility of fast attaching and detaching the whole set from the tripod. It becomes handy when frequent shoulder pad position change is assumed - switching of the shoulder support from tripod an then use it while hand shooting. Manfrotto 501PLONG quick release plate Upper movable plate is a standard Manfrotto 501PLONG quick release video camera plate. This plate serves as a convenient and proven solution for swift attaching and detaching the camera from the VCT Shoulder Base Plate or tripod. Sliding the plate backwards and forwards is a way of regulating the camera position. The movable plate has been made from lightweight aluminium with rubber pads on top to prevent unwanted frictions. Additionally, there is the key compartment placed under the plate - the key becomes useful for rods tightening and the rods mount section positioning. SHOULDER PAD Comfortable, contoured and detachable pad has been created to facilitate the work with 8Sinn VCT Shoulder Plate. Its role is to eliminate the discomfort of the camera weight on your shoulder during shooting. The pad is attached to the VCT Universal Shoulder Plate by magnets and it has four-level regulation possibility - this area contributes to the whole set ballance. FRONTAL ROD SECTION Substantial part of the VCT Shoulder Base Plate is the 15mm rod mount section. The segment has three levels of height adjustment which is convenient for different types of lenses. Additionaly, there is an innovative assembling method, with the possibility of upside down mounting, which increase the segment height range. vertical regulation range of rods is 32,5mm (from highest to lowest position), lowest possible rods position is -35mm when measured from the upper surface of the plate, highest possible rods position is 2,5mm when measured from the upper surface of the plate. MOUNTING POINTS Particular elements of 8Sinn VCT Universal Shoulder Base Plate do not disturb the operator during shooting. The plate has 1/4" threaded mounting points on both sides as well as two ARRI Standard 32mm Rosettes suitable for all accessories in the same standard

SHAPE ARRI DOVETAIL SHOULDER MOUNT The SHAPE ARRI Dovetail shoulder mount is our newly designed unit meant to be combined with ARRI style bridge plates in all 3 industry standards, (15mm LWS, 15mm Studio & 19mm Studio). The bridge plate can be adjusted front to back, depending on the weight distribution of the camera, and can be locked in the desired position with the side lever. The same can be done with the padding itself, underneath the dovetail section. You can position the padding and lock it in place with its side lever. Spring loaded stoppers are included at the front and back of the shoulder mount to prevent the top bridge plate from sliding out. To release entirely the bridge plate, simply push down on the button and the bridge plate is free. Made of sturdy CNC aluminum, the dovetail section is 12 1/2 inch long and allows a 10 ½ inches of travel for the bridge plate. It provides stability and can be combined with a variety of our handles given the two ARRI rosettes at the front part of the shoulder mount. Features Lightweight ARRI-style Dovetail shoulder mount ARRI Rosettes at the front for handle attachment Adjustable non-slip shoulder padSpring loaded stoppers at the front and backCompatible with standard ARRI style bridge plates (15mm LWS, 15mm studio and 19mm Studio).12.5” long with 10.5” of top bridge plate travelIncludes a pair of Compact Quick Handle ARRI Rosette BlackCNC machined aluminum

8Sinn Arca Swiss Baseplate Kit + Arri Dovetail Plate 5” SKU: 8-15BP+8-RPII+8-ASP-RII+8-5ADP The 8Sinn Riser Plate II is designed to be combined with the included 8Sinn 15mm Baseplate and the 8Sinn Arca Swiss Plate, which is created specifically for it. All these products combined together form a set that is the base for the camera and allows quickly releasing and switching to handheld shooting. The Arca Swiss Plate is precisely shaped on the inside to be aligned with the safety locks on the Riser Plate II - there is a release pin on one side and a lever on the other. Thanks to this, when these items are connected, they’re secured from both sides. The long slot in the middle of the Arca Swiss Plate gives the ability of connecting it to a camera cage in ways adjusted to the threaded openings on the cage with the help of 1/4“ or 3/8“ mounting screws which are supplied. The 8Sinn 15mm Baseplate has two 32mm Arri Rosettes and 15mm rod openings. On the bottom, there are dovetail guide rails. Thus, the set can be connected with the 8Sinn 5” Arri Dovetail Plate and mounted on a tripod head. This makes a great solution for more complex camera rigs. Key features Safety locks on both sides Compatible with DJI R Quick Release Plate Quick release system 2 x 32mm Arri Rosettes 15mm rod openings Aluminum made Compatibility The presented Riser Plate allows obtaining the optical center when used with the following cages: 8Sinn Z CAM E2-S6/F6/F8 Cage8Sinn Z CAM E2 Cage8Sinn Sony a7III / a7RIII Cage8Sinn Sony A7RIV Cage 8Sinn Cage for Sony a7SIII8Sinn BM Pocket Cinema Camera 4K / 6K Cage8Sinn BM Pocket Cinema Camera 4K / 6K Half Cage8Sinn Cage for Red® Komodo RED® Raptor8Sinn Cage for Panasonic GH68Sinn Panasonic S1H Cage8Sinn Cage for Canon EOS R5C8Sinn Cage for Leica SL2 / SL2-S Set includes 1 x 8Sinn 15mm Baseplate1 x  8Sinn Riser Plate II1 x 8Sinn Arca Swiss Plate1 x 8Sinn 5" Arri Dovetail Plate