MID49 Mid Kit for RED KOMODO-X

MID49 Breakout Boxes and Side Plate BundleSKU: M49-BOB-SPB-X Breakout Boxes and Side Plate Bundle for RED KOMODO-X includesBreakout Side Plate for RED KOMODO and KOMODO-XAB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini)EB-1 (RED Komodo, Komodo-X, V-Raptor)

MID49 Breakout Side Plate SKU: M49-BOB-SPL-KX Breakout Side Plate for RED KOMODO and RED KOMODO-X attaches to the side of the RED Komodo and Komodo-X and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. Two offset M4 holes matching RED's spacing allow certain 3rd party products to be attached like GDU Atlas Side Handle (Komodo, Right)When used on RED Komodo-X, rear 1/4-20's provide ideal mounting locations for Audio Breakout AB-1 (RED Komodo-X) and EXT Breakout EB-1 (RED Komodo, Komodo-X).When used on the original RED Komodo, combine with Audio Breakout AB-3 (RED Komodo) and EXT Breakout EB-1 (RED Komodo, Komodo-X).The Side Plate is compatible with RED's PL Mount support, as seen in this installation guide.Recessed cable loops in the side plate allow for clean cable management.

MID49 ARCA Top Handle Kit + 15mm LWSKU: M49-ATMK-RED-KXV15 ARCA Top Handle Kit + 15mm LW (RED Komodo, Komodo-X, V-Raptor) includes:ARCA Top Mount (RED Komodo, Komodo-X, V-Raptor)ARCA Top HandleRod Bracket (15mm LW) ARCA Top Mount (Komodo, Komodo-X, V-Raptor) attaches to two 1/4-20 screws on the top of Komodo, Komodo-X, and V-Raptor cameras. On Komodo-X, two included M4 screws can be used to attach the Top Mount to the rear portion of the camera top. Using the center ARCA Swiss standard slot, ARCA Top Handle and ARCA Top Plate (114mm) can be top-loaded or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Top mount also has 1/4-20, 3/8-16 with ARRI locating pins, and M4x20mm holes for mounting accessories. ARCA Top Handle is a lightweight sliding camera handle that attaches to ARCA Top Mount (RED Komodo, Komodo-X, V-Raptor ) and has 1/4-20 and 3/8-16 mounting holes with ARRI locating pins in standard spacing. M4x20mm threaded holes available on multiple sides for attaching Rod Bracket (15mm LW) or other ARRI M4 accessories. Hot shoe mount on the front and rear for on-camera lights, microphones, and other shoe accessories. Rod Bracket (15mm LW) holds two 15mm rods at 60mm lightweight spacing and attaches by two 1/4-20 screws 18mm apart to the back of Baseline 15mm LW baseplates to add rear rod support. M4 screws 20mm apart can be used instead to attach to products like ARCA Top Handle and ARCA Top Plate (114mm) or other devices with standard ARRI standard M4 spacing. M4x20mm threaded holes are available on top for adding additional accessories.

MID49 Baseline 15mm LW (RED KOMODO, KOMODO-X / Blackmagic Pocket 4K / FREEFLY Ember S5K Baseplate) SKU: M49-BSL-LW23-AC14 Baseline 15mm LW (RED KOMODO, KOMODO-X / Blackmagic Pocket 4K / FREEFLY Ember S5K Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Rod Bracket (15mm LW) (sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support. Individual components of this kit are also available: Baseline Core 15mm LW (23mm Platform Height)Baseline ARCA Dovetail (14.5mm Height)Baseline ARRI Dovetail Technical data Product Weight: 350gProduct Dimensions (WxLxH): 123 x 140 x 58mm